Our precleaned, Type 1 borosilicate clear or amber glass vials are washed in non-phosphate detergent, rinsed three times with tap water, and rinsed with ASTM Type-1 organic-free water to remove detergent. Post cleaning, vials are assembled with PTFE/silicone septa and open-top polypropylene caps. VOA (EPA) Vials
GC Septa. The GC septum should be routinely replaced to reduce the risk of leaks and septum particle contamination. In fact, if the instrument is in heavy use, change the septum daily. Repeated use of the same septum will result in increased coring, which may introduce a leak and/or result in septum fragments being deposited in the inlet liner.
Screw-thread sample vials are manufactured from either clear 33 expansion borosilicate clear glass (Type 1, Class A) or 51A amber glass. Vials maintain PH level and eliminate ion leaching. Choose from a polypropylene cap with a PTFE-lined foam backing or a polypropylene cap with a PTFE-lined silicone septa.
Borosilicate glass (low impurity Type I Class A) with one twist cap and pre-inserted, pre-slit PTFE/silicone septum for ease of sample preparation and autosampler needle penetration. Vial size is 12x32 mm, with a writing patch on the side. 100 vials per pack. Use for the following autosamplers and racks: SIL-20A/AC, SIL-30AC, SIL-40, LC-40
Jan 24, 2018 · This item: Aijiren Borosilicate Glass Clear Flat Bottom Headspace Vial, Beveled Finish, 10ml Capacity, Case of 100 $34.99 ($3.50/10 Items) 20mm Vial Rubber Stoppers (100 Count) Mushroom Self Healing Injection Ports Solid Seal, for Glass Vial and Liquid Culture Jars, Can Be Sterilized by Steam and Repeated Used (20mm) $8.49 ($0.85/10 Items)
Jul 10, 2012 · Introduction. In past gas chromatographic (GC) analyses, it has been reported that septa of various makes release volatile organic compounds (VOCs) when subjected to high temperatures ().These reports also revealed the frequent presence of contaminants such as finger oils from handling, or organic contaminants picked up during storage of these septa.
A GC septum is located at the top of the injection port and serves two functions: 1) providing a leak-free seal to maintain carrier gas pressure inside the system. 2) handling repeated puncturing by a syringe needle for sample introduction purposes without severe coring or leaking. Temperature-Programming: When performing temperature-programmed
Jun 10, 2020 · VOA/TOC Clear Vials, 40mL - 100/PK - Borosilicate Glass - ASTM/USP Type I, Class B - PP Caps with PTFE Septa - Shrink-Wrapped - Pre-Assembled - Eisco Labs $119.99 $ 119 . 99 Kesell Clear Glass Sample Vials, Mini Empty Glass Bottles with Screw Cap Capacity 20ml (0.7 Oz), Pack of 20 284
Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency. Bleed temperature optimized (BTO) septa are
Advanced Green inlet septa eliminate sticking and reduce coring. Bleed temperature optimized (BTO) inlet septa are preconditioned and ready to use with low-bleed, mass spec capillary columns. Our long-life septa are specially formed for extended use, meaning less downtime.
Product Details Features The preferred septum for autosamplers Pre-pierced for extended life and reduced coring Ideal for overnight runs Up to 400 injections per septum Plasma coating eliminates sticking Maximum injection port temperature 350 °C Soft, 45 Durometer, easy on autosampler needles Blister packaging for cleanliness and convenience
I-Chem. Clear borosilicate glass with 0.060 in. Thin Septa 40 mL clear septa vials feature a thin (0.060”) PTFE/silicone septa. The septum is easy to puncture with syringe needles and is ultrasonically bonded to the 24-414 polypropylene closure. No adhesive is used.
GC injection port septa High quality CenterGuide™ for centered needle guidance for a perfect fit Highest septum quality for minimal bleeding, even at high temperatures up to 400 °C (Shimadzu plug septa up to 300 °C) Precision trough for a perfect fit Special coating Related Products: Injection Septum Compare this item
General Purpose Septa for GC. Aijiren’s general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C.
Molded Septa are manufactured from high quality, low bleed material that uses the same exclusive LB-2 rubber formulation chromatographers are accustomed to using. Design. Solid Disc. Type. Septa. For Use With (Equipment) Low Bleed GC-MS Columns. Temperature (Metric) Max. 350°C.