Molded Septa are manufactured from high quality, low bleed material that uses the same exclusive LB-2 rubber formulation chromatographers are accustomed to using. Design. Solid Disc. Type. Septa. For Use With (Equipment) Low Bleed GC-MS Columns. Temperature (Metric) Max. 350°C.
Septa for use with general chromatography vials PTFE/Red Rubber Septa: (PTFE/RR) PTFE/Red Rubber septa are the most popular and economical choice for general gas chromatography applications. These septa are used primarily for routine analysis in gas chromatography with FID, TCD and FPD detectors.
mixtures. Polypropylene septa offer better solvent compatibility compared to polyethylene, but piercing force is slightly higher. Viton (V1) septa Viton septa are used in situations where a resealable septum is required for a sample matrix that aggressively attacks all other materials. Viton offers chemical resistance similar to PTFE along with
Stoppers, also known as bungs, are used to give an airtight seal to laboratory flasks and test tubes by fitting tightly inside the neck of the container and preventing material from spilling. Stoppers can be made of glass, cork, rubber, or silicone. They are typically designed with a conical shape, but straight, flanged, and tapered options are
Septa chemical compatibility. Solvent PTFE PTFE/Silicone PTFE/Silicone/PTFE* PTFE/Red rubber Fluoroelastomer PTFE/Butyl Acetonitrile Hydrocarbons (hexane, heptane, methane) Methanol Benzene THF Toluene DMF DMSO Ether Chlorinated solvents (methylene chloride) Alcohols (ethanol) Acetic acid Acetone Phenol Cyclohexane
Polytetrafluoroethylene ( PTFE) is a synthetic fluoropolymer of tetrafluoroethylene and is a PFAS that has numerous applications. The commonly known brand name of PTFE-based composition is Teflon by Chemours, [3] a spin-off from DuPont, which originally discovered the compound in 1938. [3]
Jul 10, 2012 · Different septa shown in Figures 2A–2D used in this study were obtained from various sources, including: SGE Analytical Science (Australia, part number 041904; suggested application maximum temperature of 400°C); yellow PTFE coated (part number 041827 suggested application maximum temperature of 200°C); Aijiren Tech BTO (part number THC31303230 no suggestion of application maximum
Overview Diferent septa material for LC and GC applications There are many diferent types of materials used to produce the septa found in LC and GC vial caps. This document will provide you with the technical guidance you need in order to make the right selection. Choosing the right septa
Septa are made from different materials. See below for definitions and uses of different types of septa materials. Rubber septa. Used primarily for routine analysis in gas chromatography. Offers moderate ability to reseal and good chemical inertness. Not recommended for multiple injections or holding samples for further analysis.
Jul 2, 2013 · Repeat steps 4 and 5 for flask 2. Purge the syringe by inserting the needle through the septum of the solvent flask and into the headspace of the flask. Draw up the inert atmosphere into the syringe. Remove the needle from the flask and expel the gas from the syringe (Fig. 14, D). Repeat 3–4 times.
Select the Nalgene dilution bottle that works for you. Nalgene dilution bottles make 1/10 and 1/100 dilutions simple. Graduated at 90mL and 99mL, with plenty of head space for reagent additions after dilution, often eliminating the need to transfer diluted samples to another container for further process steps.
Headspace Caps and Septa Choose the right septa for your analysis. Although a wide variety of septa is chemical compatibility and temperature are the most critical to the analysis. Temperature applies not only to the vial, but also to the temperature of the instrument’s needle used for pressurization and sample transfer, which is
The C&G 60 mL precleaned VOA (volatile organic compound) vial is mainly used in research laboratories or in chemical industries. It is suitable for use with autosamplers, solid cap and liners for analysis. This L3 vial comes with a 24-414 white PTFE septa cap which offers tight sealing of sample. Compare this item.
Analytical Vials. Vials play a significant role in analytical analysis and result reproducibility. Vials must be inert and free of extractables or leachables to prevent affecting results. Using certified, application-specific, contaminant-free vials can significantly reduce risk. We offer a broad spectrum of Supelco ® products including
Choosing the right septa and closures for your analysis is critical to ensure chemical compatibility with your sample and solvents and protect sample integrity and prevent contamination. Screw and snap caps are usually made of plastic, mostly polypropylene (PP) or polyethylene (PE), whereas seals for crimp-top vials are made from aluminum.