Overview Diferent septa material for LC and GC applications There are many diferent types of materials used to produce the septa found in LC and GC vial caps. This document will provide you with the technical guidance you need in order to make the right selection. Choosing the right septa
Septa are available in a variety of materials and thicknesses. PTFE Natural Rubber are moderately priced seals for GC and HPLC with good chemical properties. They are ideal for multiple injections due to high resealability, but not as easy to penetrate as PTFE/RR. PTFE/High Performance Rubber is a highly pure synthetic red rubber septum that
Septa. A wide range of serrated and non-serrated septa, and sleeve stoppers are available for use as temporary closures for glassware joints, tubes, bottles, NMR tubes, ampules, and cannulation techniques in air-sensitive chemistry. To protect your valuable contents in the vessels or containers from the atmosphere, our range of septa provide
Aijiren Tech Nalgene. Teflon® FEP Bottles RCF to 4,000 x g Withstand temperatures from -100° to +150°C Flat bottoms Autoclavable bottles have an 80% capacity (approx. 200 mL) in refrigerated centrifuges. Bottles include 38 mm Tefzel® ETFE screw caps. Dimensions (o.d. x H, mm): 62 x 122.
The Aijiren Technologies inlet septa is made from strong silicone material and works well even at 35 degree C temperatures. This septa is compatible to use with , , 4890, , , GC columns. Application: For , , 4890, , , GCs This product is only available to. Compare this item.
VWR 150ul 2ml vial inserts price-HPLC Vial Inserts. USA 150ul insert Perkin Elmer supplier – femke bertels Call us Registered Office Well Group Scientific (aijiren 2ml HPLC vial insert manufacturer) Ltd. Call1-800-440-7876 Fax1-978-251-4537 [email protected] Addrress7 Doris Drive, Unit #6A Chelmsford, MA 01863.
Wheaton headspace vials accept 20 mm aluminum seals Rounded shoulders and bottoms, allowing for even heating and safer operation at higher pressures Manufactured from Type I borosilicate glass Top provides a tighter seal with your septa O.D. x Height: 23 x 75 mm Capacity: 20 mL. Related Products: 20 Ml Glass Vials. Compare this item.
A GC septum is located at the top of the injection port and serves two functions: 1) providing a leak-free seal to maintain carrier gas pressure inside the system. 2) handling repeated puncturing by a syringe needle for sample introduction purposes without severe coring or leaking. Temperature-Programming: When performing temperature-programmed
T/S/T septa provide superior performance with any autosampler employing a large diameter, blunt-tip needle . T/S/T septa can have benefits when working with solvents that tend to attack silicone by protecting both sides of the elastomer . PTFE Disk Septa A solid disk of 0 .010” thick pure PTFE offers superior chemical inertness against the most
Chemglass. Replacement septa for use with MW-102 open-top screw caps on Minum-Ware® glassware components. Septa are made of silicone rubber with one side having a RED PTFE face, while the opposite side has an ultrathin covering of polypropylene to prevent needle coring when penetrating septa. Compare this item.
MilliporeSigma. of 6.9 +/- 0.2 at 25C. It can be stored at 15-25C (protected from light) for 12 months. A single box contains 4 bottles of 300 mL of fluid, each bottle with a screw cap with septum closure that reduces the risk of cross-contamination and optimizes the disinfection procedures. Synonyms: Diluting.
Supplied with open top polypropylene caps and Teflon®/FDA grade silicone septa Include a polyproylene cap and Teflon/Silicone/polypropylene liner to ensure easier sampling and extraction 1755C64 through 1755C80 are clear; 1755D18 through 1755D28 are amber. Related Products: Glass Bottle Teflon Cap Compare this item Narrow-Mouth Septa Bottles I-Chem
Septa Selection Tool | Aijiren Tech Scientific - USSealing surface of Butyl and PTFE affects a more positive seal than non-PTFE-faced septa. Ideal choice for temperatures below 1 Whatsapp: +8618057059123
compatibility, effective sealing/resealing and low penetration force make PTFE/silicone septa suitable for all types of chromatographic applications. A thin film of PTFE is laminated to the side of the septum that faces the sample to limit exposure of the elastomer to the solvent. PTFE/Silicone septa are ideal for use in most HPLC and
Techne (Cole-Parmer) coupling attached to underside of cap. Cap is plastic with a Teflon® liner and silicone rubber gasket which seals against the mouth of flask. Both liner and coupling are removable from cap. Side arms and ports have plastic screw caps with silicone rubber liners. 9382E50 through E65 have two….